Makerbot Replicator 2 Extruder Filament Drive Upgrade

24 Sep


Time for yet another upgrade for our faithful MakerBot Replicator 2 3D printer, this time we are going to be upgrading the plastic filament drive mechanism of the extruder with a better all metal version from Fabberworld. The filament drive upgrade comes as a full kit containing all precisely CNC machined parts from aluminum that will replace the plastic parts, along with stainless steel screws, replacement bearing, spring and even a pulley gear for the motor. The kit is designed for Replicator 2 3D printers that have a total thickness of the plastic parts of 20mm as there are models of the printer with slimmer 15mm parts, but we have figured out an easy way to install it even on these. We are going to get back to that in a moment however. There is also a version of the upgrade available for MakerBot Replicator 2X 3D printer where you essentially get two kits – a left and right one for each of the motors of the dual extruder 3D printer.


Probably some of you will ask why we would want to upgrade the standard plastic parts with aluminum ones, the answer is simple – plastic wears off easily, it breaks and it does not handle that well a lot of heat. The standard plastic parts are from injection molded ABS plastic that is pretty durable and resistant to high temperature, but over time it can start to wear off from abrasive filaments and to deform or even break from the constant high temperatures around it. Back on the metal upgrade kit, it not only replaces the plastic parts, but also comes with some improvements that help you get more consistent and problem free prints and these actually do seem to work well. On the top “lever” where the filament goes in there is a wider opening to allow the PTFE tube to slide in and make the filament slide in easily when you load it into the extruder, though if you are not using the Teflon filament guide tube this can actually make it a bit harder to load filament. The included MK7 pulley that replaces the standard one has a smaller gap where the filament goes through that is more suitable for the 1.75mm filament that the MakerBot Replicator 2 uses. The standard pulley that our printer came up with seems to be more suitable for 3mm filaments than the 1.75mm one that we are actually using, so after the upgrade you should also get more contact surface and force pulling the filament through the nozzle and thus in theory less problems with filament jams.


Now, how to install the filament drive upgrade for the extruder of MakerBot Replicator 2 3D printers that come with 15mm thickness of the plastic parts. We have figured out a way to do everything as easy as with 20mm models, all you would need are two 5mm spacers to bring the motor back the needed extra space. The only thing that you would need to remove is the fan grill in front of the cooling fan of the extruder and then the two screws holding everything in place will be long enough to accommodate the 5mm spacers (you can use two 2.5mm ones or a different combination if you do not have a single 5mm ones). The cooling fan blades are small and if you do everything with a bit of extra caution around the extruder while the printer is operating you should not have trouble even with the fan grill missing. Alternatively you can look for screws with extra 5mm length and keep the full build with the fan grill, but finding only two 5mm spacers should be easier and you can probably build them with existing smaller spacers that you may have lying around.

For the price that the MakerBot Replicator 2 3D printer sells one would expect to get a 3D printer that is well built and very durable with no problems while printing, but our experience has shown that after you get the device you still need to do some upgrading and tuning as you go. One of the good upgrades that you might want to do in order to have less problems on the long term with issues working with the 3D printer is the filament drive upgrade of the extruder, though it is not the only one. Do note however that some of the upgrades, including this one are not as easy to be performed by people that are new to 3D printing and are not familiar with their 3D printers as it requires to disassemble the extruder and then assemble it again with the new parts installed.

Visit the product page of the Makerbot Replicator 2 Extruder Filament Drive Upgrade…

Other Similar Publications:

Leave a Reply

Your email address will not be published. Required fields are marked *